Litchfield, NH

I believe the burning smell was caused by loose insulation threads making contact with the hest exchanger. I removed the threads and the smell went away.

Replaced the failed indirect water tank. Checked for leaks and there was none. Replaced the domestic water expansion tank. Completed the maintenance on the boiler. I started off with checking all the wiring connections and everything looked good. Next I pulled the flame sensor and cleaned it. I vacuumed out the burners and the burner box. I checked incoming and outgoing gas pressure and those were accordance to manufacturer specifications. I inspected all the boiler accessories and the only thing that I found was that the high vent was leaking water. Lastly I ran the unit and performed a combustion analyzer test. This checks the unit CO, CO2 and oxygen levels. The boiler was running good. I bled the air from the hot and cold water lines before I left.

Boiler flow switch is bad. I installed temporary low water cut off in order to keep the boiler on line for the residents. We will order the switch and return this week to replace it.

Replacement of the existing tank-style water heater. Install a 40-gallon indirect tank as a new zone off the existing boiler. The boiler was prepiped and set up to allow for this plan in the future.

Completed the furnace maintenance today. I started off with checking all the wiring connections and everything looked good. Next I pulled and cleaned the flame sensor. I replaced the air filter with a 20x25x5 air bear filter. I checked incoming and outgoing gas pressures and those were according to manufacture specifications. Lastly I ran the unit in low and high fire and performed a combustion analyzer test. This checks the units CO, CO2 and oxygen levels. The furnace was running great. It is too cold outside to complete the AC maintenance so we can reschedule for April to May.

Completed the plumbing maintenance and inspection. I started off with draining both electric water heaters. I checked the anode rods and those were in good condition. I checked the expansion tank and that was good as well. I labeled a few emergency shut off's and I showed the client where they were. I went around the house and checked out all the drains, water lines and fixtures, everything looked good.

Add in a pressure reducing valve.

Replaced water heater.

Replacement of the existing hydronic air handler and central air system with a new high-efficiency hybrid heat pump system. A new First Co hydronic air handler will be installed. This unit features a variable-speed motor for quiet and efficient operation, and it has a built-in hydronic coil for heating. We will install a new return air base with a new air filtration system. The new coil will be re-connected to the existing oil boiler zone, just as the previous system was. The existing ductwork connections will be remade to the new system, and both returns will be reconnected. A new lineset will be run from the outdoor unit to the interior. If a new line cannot be run, we will purge and clean the existing lineset using our cleaning agent. Outside, a new heat pump unit will be installed on the existing concrete pad. The new unit will be elevated on "footies" to assist with defrost cycles and prevent freezing. A new Lennox s40 smart Wi-Fi thermostat will control the system, with a bala

Installed Lennox heat pump

Water heater estimate.

Add waste water check valve in basement trap. Add water hammer arrestors to washing machine valve. Perform comprehensive water test to drop off at NH State certified water testing facility.

Install valves for kitchen sink and replace sprayer

Water heater isn't keeping up. Client wanted the water heater replaced.

Replaced fill valve on toilet

Replace toilet. Cutout old iron flange and add stainless steel flange. Replace Kohler canister gasket. Measure shower for replacement.

I started off with doing the maintenance on the Rinnai floor heater. I vacuumed the air filters. I vacuumed out the whole inside of the unit and the blower wheels. I checked all the electrical connections and everything looked good. I checked all the vent pipe connections for carbon monoxide leaks and there was none. I used an electronic sniffer on the gas lines and there is no leaks as well. The bathroom fan was extremely dirty so there was poor air flow. I took it all apart and cleaned it. It was a night and day difference with the amount of suction now. Lastly I took a look at the water heater and the date says it was manufactured in September of 2005. There is a water filter that filters the water before the tank and it is extremely dirty. I would highly recommend replacing the tank due to the age because if that tank was to fail there would be 40 plus gallons of water all over the floor and the ceiling below.

Install bath rm fan

To permanently resolve the leak and ensure safe, consistent water temperatures, we recommend a complete internal rebuild of the shower valve using genuine OEM Kohler replacement parts. We do not recommend a "partial" repair, as disturbing the old, hardened O-rings on the secondary components will likely cause new leaks behind the finished wall.

Project Overview During our recent service visit, Jack, noted significant scale buildup and active corrosion on several internal valves and fittings within your 11-year-old Rinnai tankless water heater. Given the age of the unit (originally installed during the home's construction) and the cost of rebuilding these internal components, we strongly recommend proactively replacing the unit. Upgrading now prevents a sudden failure and provides you with a brand-new system, full factory warranties, and renewed efficiency. Scope of Work 1. Equipment Removal & Installation Removal: Safely drain, disconnect, and remove the existing 11-year-old Rinnai tankless water heater. Installation: Supply and mount a new, high-efficiency Rinnai Tankless Water Heater in the existing location. Connections: Install new hot and cold water isolation valves (required for future maintenance and flushing) and reconnect to the existing gas and water lines. 2. Recirculation System Integration: Your home is a

Found a huge crack in the bottom of the indirect water tank. The supply valve is shut. I also found that the domestic water expansion tank has failed. The water tank is from 1998. I will send over an estimate to replace the hot water tank and the expansion tank. I would also recommend a maintenance to be done on the boiler if it hasn't been done recently.

I reccomend replacing water tank due to high TDS on hit water, yellow color, and anode rod being completely gone.

Replace anode rod. Cut out corroded fitting and replace. Check for leaks and purge air from hot water lines. Thank you!

Completed the plumbing maintenance. I flushed the hot water tanks. I pulled the anode rods and they looked in decent shape. I checked the expansion tanks and those were good. I labeled a few emergency shut off's. Lastly I checked the water pipes and drains and everything looked good.

Cut open wall to repair drain.Have to come back water treatment equipment was draining into line.